Install a Secure Event Connector on an SDC Virtual Machine

The Secure Event Connector (SEC) receives events from ASA and FDM-managed devices and forwards them to the Cisco cloud. CDO displays the events on the Event Logging page so that administrators can analyze them there or by using Cisco Secure Cloud Analytics.

You can install one SEC on the same virtual machine as a Secure Device Connector, if you have one; or you can install the SEC on it's own CDO Connector virtual machine that you maintain in your network.

This article describes installing an SEC on the same virtual machine as an SDC. If you want to install more SECs see Installing an SEC Using a CDO Image or Install an SEC Using Your VM Image.

Before you begin

  • Purchase the Cisco Security and Analytics Logging, Logging and Troubleshooting license. Or, If you want to try Cisco Security and Analytics Logging out first, log in to CDO, and on the main navigation bar, choose Analytics > Event Logging and click Request Trial. You may also purchase the Logging Analytics and Detection and Total Network Analytics and Monitoring licenses to apply Secure Cloud Analytics to the events.

  • Make sure your SDC has been installed. If you need to install an SDC, follow one of these procedures:

  • Make sure the SDC is communicating with CDO:

    1. In the left pane, click Tools & Services > Secure Connectors.

    2. Make sure that the SDC's last heartbeat was less than 10 minutes prior to the installation of the SEC and that the SDC's status is active.

  • System Requirements - Assign additional CPUs and memory to the virtual machine running the SDC:

    • CPU: Assign an additional 4 CPUs to accommodate the SEC to make a total of 6 CPU.

    • Memory: Assign an additional 8 GB of memory for the SEC to make a total of 10 GB of memory.

      After you have updated the CPU and memory on the VM to accommodate the SEC, power on the VM and ensure that the Secure Connectors page indicates that the SDC is in the "Active" state.

Procedure

Step 1

Log in to CDO.

Step 2

From the left pane, click Tools & Services > Secure Connectors.

Step 3

Click the icon and then click Secure Event Connector.

Step 4

Skip Step 1 of the wizard and go to Step 2. In step 2 of the wizard, click the link to Copy SEC Bootstrap Data.

Step 5

Open a terminal window and log into the SDC as the "cdo" user.

Step 6

Once logged in, switch to the "sdc" user. When prompted for a password, enter the password for the "cdo" user. Here is an example of those commands: 

[cdo@sdc-vm ~]$ sudo su sdc
[sudo] password for cdo: <type password for cdo user>
[sdc@sdc-vm ~]$

Step 7

At the prompt, run the sec.sh setup script:

[sdc@sdc-vm ~]$ /usr/local/cdo/toolkit/sec.sh setup

Step 8

At the end of the prompt, paste the bootstrap data you copied in step 4 and press Enter.

Please copy the bootstrap data from Setup Secure Event Connector page of CDO: KJHYFuYTFuIGhiJKlKnJHvHfgxTewrtwE
RtyFUiyIOHKNkJbKhvhgyRStwterTyufGUihoJpojP9UOoiUY8VHHGFXREWRtygfhVjhkOuihIuyftyXtfcghvjbkhB=

After the SEC is onboarded, the sec.sh runs a script to check on the health of the SEC. If all the health checks are "green," the health check sends a sample event to the Event Log. The sample event shows up in the Event Log as a policy named "sec-health-check."

If you receive a message that the registration failed or that the SEC onboarding failed, go to Troubleshooting Secure Event connector Onboarding Failures.

Step 9

Determine if the VM on which the SDC and SEC are running needs additional configuration:

What to do next

Return to Implementing Secure Logging Analytics (SaaS) for ASA Devices Implementing Secure Logging Analytics (SaaS) for FDM-Managed Devices.